2.40:??? - Fixed bug with elastic mode/\r\n/2.39:??? - Doubled visible data in sniffer when using ASCII/\r\n/ - Valid fonts for Line Feed and Carriage return characters/\r\n/2.38??? - No change/\r\n/2.37??? - Fixed power down bugs from revision 2.28/\r\n/2.36??? - Added a timer on the Pulse Counter/\r\n/2.35??? - Implemented the Pulse Counter/\r\n/2.34??? - Removed exponential average from volt meter measurements to improve response time/\r\n/ - Fixed bugs with serial transmission/\r\n/2.33??? - Cursors can go beyond the visible screen/\r\n/2.32??? - Distinct Start of Frame for fast and slow sampling rates/\r\n/2.31??? - Added Start of Frame to the serial interface/\r\n/2.30??? - Added the METER measurement to the interface protocol/\r\n/2.29??? - Updated serial interface protocol/\r\n/2.28??? - Reference waveforms on XY mode/\r\n/2.27??? - No change/\r\n/2.26??? - Option to invert the Chip Select pin in the SPI sniffer/\r\n/2.25??? - Minor cleanup to the source code/\r\n/2.24??? - Added the "Restore Settings" command to the inteface protocol/\r\n/ - On the first power up, the device will enter the calibration function/\r\n/2.23??? - no change/\r\n/2.22??? - Optimization on I2C sniffer/\r\n/2.21??? - The Frequency Counter now works on any digital pin (selected with the trigger source)/\r\n/ - On the external trigger, the maximum frequency is 12MHz/\r\n/ - On the logic channel pins, the maximum frequency is 16MHz/\r\n/ - The trigger mark is shown when a logic input is the trigger source/\r\n/ - The trigger direction is toggled when selecting a digital trigger source/\r\n/ - Fixed SPI sniffer bug caused when data is being transmitted before the sniffer has started/\r\n/ - Added graphic indication of the SPI configuration in the menu/\r\n/ - Optimizations on UART sniffer/\r\n/2.20??? - Fixed bug created in 2.19 that disabled low level interrupts/\r\n/2.19??? - Fixed SPI Sniffer bugs:/\r\n/ - Fixed bug when receiving a very long stream of data/\r\n/ - Fixed bug when CPOL was 1/\r\n/ - Fixed bug that enabled the ASCII mode when CPHA was 1/\r\n/ - Verified Sniffer SPI clock operation range:/\r\n/ - Correct operation up to 439kHz/\r\n/ - Above 439kHz, MOSI still works up to 8MHz/\r\n/2.18??? - Fixed overflow when displaying TPost/\r\n/2.17??? - UART Sniffer can decode 5,6,7 data bit sizes, in addition to 8 which was fixed./\r\n/ - Menu timeout after 1 minute/\r\n/2.16??? - Fixed bug on the UART sniffer/\r\n/2.15??? - Minor bug fixed in the XY mode when the ROLL is enabled./\r\n/2.14??? - Minor improvements to UI/\r\n/2.13??? - Prevent going to sleep when connected to USB/\r\n/2.12??? - Updated interface protocol. The PC interface needs to be updated as well./\r\n/2.11??? - Better handling when stopping the scope/\r\n/ - Added Trigger Timeout control/\r\n/2.10??? - USB restart when USB communication lost/\r\n/2.09??? - Code optimizations/\r\n/2.08??? - XY mode: 1.- The graph can be moved vertically, 2.- Cursors added/\r\n/2.07??? - If VCC is lower than about 3.15V: 1.- An empty battery icon will appear 2.- No writes to EEPROM/\r\n/2.06??? - Fixed bug in Frequency Counter/\r\n/2.05??? - Fxed bug in I2C sniffer/\r\n/2.04??? - No change/\r\n/2.03??? - Display's power off sequence fixed/\r\n/2.02??? - Extended reset signal on the power up of the display, added delay before initializing display/\r\n/2.01??? - Extended reset signal on the power up of the display/\r\n/2.00??? - Getting ready to send out a newsletter, reving up to 2.00
Older revision history is in the readme.txt file, along with the HEX file
