XMEGA Xprotolab

Manual EN Translations	Schematics	Code	Hex	BOM	Interface	Videos	Pictures	FAQ	Forums

The Xprotolab is the first mixed signal oscilloscope with an arbitrary waveform generator in a DIP module. It measures only 1 x 1.6 inches, and can be mounted directly on a breadboard. The Xprotolab can also be used as a development board for the AVR XMEGA microcontroller.

Features:

• Mixed Signal Oscilloscope: Simultaneous sampling of analog and digital signals.
• Advanced Trigger: Normal / Single / Auto, with rising or falling edge and adjustable trigger level.
• Meter Mode: Average, Peak to peak and Frequency readout.
• XY Mode:
  - Plot Lissajous patterns
  - See the phase difference between two waveforms
  - V/I Curve tracer with an external resistor
• Spectrum Analyzer with different windowing options and selectable vertical log.
• Horizontal and Vertical Cursors with automatic waveform measurements.
• Arbitrary Waveform Generator with Sweep on all parameters.
• Display options: Persistence, Different grid options, and more.

The Xprotolab was awarded as one of the 100 Hot Products of 2011, by the EDN magazine.

Customer Reviews:

I have to admit, this device worth every penny!There are several "pcb like" oscilloscopes on the market, however I choose this because it have an x-y input.Screen is small but I can read it easily. I am almost 50 years old, I haven't my twenty's vision, however I'm not wearing yet eyeglasses either. In my condition I can read every character on screen.The most impressive is the huge number of functions in this tiny device!I place my own DIY pcb behind it, to turn it into a powerful fully parametrical component tester (Tracer). Since then I make amazing measurements which I couldn't done them before, and all in an absolutely portable way.For power supply I use a micro-usb phone charger or a $5 powerbank, which last for days or even weeks!Thanks again!Wish list:Hide usb and serial connector behind screen, to make device even smaller, at the same screen size.May add a backwards menu button.Faster Auto trigger if possiblePlotless trace at XY mode.

I have both XProtoLab's, with screen and without. The one with the screen works very well when you can see it. You need a very good magnifier. The other you have to use the interface. I am running windows. The interface has so many problems I am just not sure where to begin. They have not updated it since I bought mine. Everything on the site is last YEAR.
The screen crashes but the board is still working. It is so unstable that its unusable. I would like to see some updates and if you have new firmware for the boards I would to get it.
Larry

This product is worth every cent! The display is beautiful and the features are rich. It is perfect for audio applications. You will have a lot of fun with this little device. Guaranteed.

However, there are two problems I'd like to point out:

Problem 1:
It is IMPOSSIBLE to install the drivers on Windows 8. Microsoft doesn't allow you to install this driver unless you have a valid certificate (which one has to buy for sixty dollars). This is not necessarily a problem of the device itself, but rather a problem created by Microsoft.

Problem 2:
When one uses the waveform generator, the amplitude changes when generating signals over 10kHz. This problem should be fixable to an extent by code though... :/

Unbelievably useful UI. Every time I use it, I'm amazed at how intuitive a 4 button interface can be... to a full-function DSO, and AWG, and everything else. Look at any DSO/analog scope... all those controls. Look at the Gabotronics PC interface... the 4 button UI is actually more intuitive and easier to use! Amazing, especially when you consider how many 4-button wristwatches out there make setting the time nearly impossible. I've actually had to use a manual to figure out a stupid wristwatch. This little scope... 5 minutes of messing around and I was functional... no manual, nor any previous DSO experience (just old-school analog). It just makes perfect sense; it just does everything I want.

Best on site oscope to trouble shoot my installed arduino projects. I can carry this into my backyard or to a friends to work on projects. Most can't believe I am serious when I bring it out then marvel when I use it. One friend said it was cost effective to attach to a project and leave it. I love it so much I bought its parent the mini. Great job.

You may also be interested in this/these product(s)

XMEGA Xminilab $59.00

Kit to build Xprotolab $35.00 $25.00 You Save: $10.00

Bluetooth Module $35.00

Xprotolab Portable $98.00